1
Refer to the exhibit. Communication between two peers has
failed. Based on the output that is shown, what is the most likely
cause?
interface reset
unplugged cable
improper LMI type
PPP negotiation failure
2
Refer to the exhibit. A network administrator
is tasked with completing the Frame Relay topology that interconnects
two remote sites. How should the point-to-point subinterfaces be
configured on HQ to complete the topology?
frame-relay interface-dlci 103 on Serial 0/0/0.1
frame-relay interface-dlci 203 on Serial 0/0/0.2
frame-relay interface-dlci 301 on Serial 0/0/0.1
frame-relay interface-dlci 302 on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 103 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 203 broadcast on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 301 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 302 broadcast on Serial 0/0/0.2
3
Which data link layer encapsulation protocol is used by default for serial connections between two Cisco routers?
ATM
Frame Relay
HDLC
PPP
SDLC
4
Refer to the exhibit. Company ABC expanded its business and recently opened a new branch office in another country. IPv6 addresses
have been used for the company network. The data servers Server1 and
Server2 run applications which require end-to-end functionality, with
unmodified packets that are forwarded from the source to the
destination. The edge routers R1 and R2 support dual stack configuration. What solution should be deployed at the edge of the company network in order to successfully interconnect both offices?
a new WAN service supporting only IPv6
NAT overload to map inside IPv6 addresses to outside IPv4 address
a manually configured IPv6 tunnel between the edge routers R1 and R2
static NAT to map inside IPv6 addresses of the servers to an outside IPv4 address and dynamic NAT for the rest of the inside IPv6 addresses
5
Which variable is permitted or denied by a standard access control list?
protocol type
source IP address
source MAC address
destination IP address
destination MAC address
6
Refer to the exhibit. The link between the CTRL and BR_1 routers is configured as shown in the exhibit. Why are the routers unable to establish a PPP session?
The clock rate must be 56000.
The usernames are misconfigured.
The IP addresses are on different subnets.
The clock rate is configured on the wrong end of the link.
The CHAP passwords must be different on the two routers.
Interface serial 0/0/0 on CTRL must connect to interface serial 0/0/1 on BR_1.
7
Which three statements accurately describe a security policy? (Choose three.)
It creates a basis for legal action if necessary.
It defines a process for managing security violations.
It defines acceptable and unacceptable use of network resources.
The remote access policy is a component of the security policy that governs acceptable use of e-mail systems.
It is kept private from users to prevent the possibility of circumventing security measures.
It provides step-by-step procedures to harden routers and other network devices.
8
A network administrator has changed the VLAN configurations on
his network switches over the past weekend. How can the administrator
determine if the additions and changes improved performance and
availability on the company intranet?
Conduct a performance test and compare with the baseline that was established previously.
Interview departmental secretaries and determine if they think load time for web pages has improved.
Determine performance on the intranet by monitoring load times of company web pages from remote sites.
Compare the hit counts on the company web server for the current week to the values that were recorded in previous weeks.
9
Refer to the exhibit. Headquarters is connected through the
Internet to branch office A and branch office B. Which WAN technology
would be best suited to provide secure connectivity between headquarters
and both branch offices?
ATM
VPN
ISDN
Frame Relay
broadband DSL
10
Which statement about a VPN is true?
VPN link establishment and maintenance is provided by LCP.
DLCI addresses are used to identify each end of the VPN tunnel.
VPNs use virtual Layer 3 connections that are routed through the Internet.
Only IP packets can be encapsulated by a VPN for tunneling through the Internet.
11
A company is deciding which WAN connection type it should
implement between its main office and branch offices. The company wants
to use a cost-effective service that provides virtual circuits between
each office. The company also wants to be able to transmit
variable-length packets on these circuits. Which solution best meets
these requirements?
ATM
HDLC
ISDN
Frame Relay
12
A technician is talking to a colleague at a rival company and
comparing DSL transfer rates between the two companies. Both companies
are in the same city, use the same service provider, and have the same
rate/service plan. What is the explanation for why company 1 reports
higher download speeds than company 2 reports?
Company 1 only uses microfilters at branch locations.
Company 1 has a lower volume of POTS traffic than company 2 has.
Company 2 is located farther from the service provider than company 1 is.
Company 2 shares the connection to the DSLAM with more clients than company 1 shares with.
13
Refer to the exhibit. What is placed in the address field in the header of a frame that will travel from the DC router to the Orlando router?
DLCI 123
DLCI 321
10.10.10.25
10.10.10.26
MAC address of the Orlando router
14
Refer to the exhibit. This router is being configured to use SDM, but the SDM interface of the router cannot be accessed. What is the cause of the problem?
The VTY lines are not configured correctly.
The HTTP timeout policy is not configured correctly.
The authentication method is not configured correctly.
The username and password are not configured correctly.
15
Which two devices can be used by teleworkers who need to connect
to the company network across the PSTN for a few hours a day? (Choose
two.)
router
CSU/DSU
DSL modem
cable modem
access server
dialup modem
16
An administrator is configuring a dual stack router with IPv6
and IPv4 using RIPng. The administrator receives an error message when
trying to enter the IPv4 routes into RIPng. What is the cause of the
problem?
When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of the newer technology.
Incorrect IPv4 addresses are entered on the router interfaces.
RIPng is incompatible with dual-stack technology.
IPv4 is incompatible with RIPng.
17
What is the function of an intrusion detection system on a network?
to restrict access to only authorized users
to detect attacks against a network and send logs to a management console
to prevents attack against the network and provide active defense mechanisms
to detect and prevent most viruses and many Trojan horse applications from spreading in the network
18
Refer to the exhibit. All devices are configured as shown in
the exhibit. PC1 is unable to ping the default gateway. What is the
cause of the problem?
The default gateway is in the wrong subnet.
STP has blocked the port that PC1 is connected to.
Port Fa0/2 on S2 is assigned to the wrong VLAN.
S2 has the wrong IP address assigned to the VLAN30 interface.
19
When Frame Relay encapsulation is used, what feature provides flow control and exchanges information about the status of virtual circuits?
LCP
LMI
DLCI
Inverse ARP
20
A system administrator must provide Internet connectivity for
ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure DHCP and static NAT.
Configure dynamic NAT for ten users.
Configure static NAT for all ten users.
Configure dynamic NAT with overload.
21
A company is looking for a WAN solution to connect its
headquarters site to four remote sites. What are two advantages that
dedicated leased lines provide compared to a shared Frame Relay
solution? (Choose two.)
reduced jitter
reduced costs
reduced latency
the ability to burst above guaranteed bandwidth
the ability to borrow unused bandwidth from the leased lines of other customers
22
What will be the result of adding the command ip dhcp
excluded-address 192.168.24.1 192.168.24.5 to the configuration of a
local router that has been configured as a DHCP server?
Traffic that is destined for 192.168.24.1 and 192.168.24.5 will be dropped by the router.
Traffic will not be routed from clients with addresses between 192.168.24.1 and 192.168.24.5.
The DHCP server will not issue the addresses ranging from 192.168.24.1 to 192.168.24.5.
The router will ignore all traffic that comes from the DHCP servers with addresses 192.168.24.1 and 192.168.24.5.
23
Refer to the exhibit. A host connected to Fa0/0 is unable to
acquire an IP address from the DHCP server. The output of the debug ip
dhcp server command shows “DHCPD: there is no address pool for
192.168.3.17?. What is the problem?
The address 192.168.3.17 address is already in use by Fa0/0.
The pool of addresses for the 192Network pool is configured incorrectly.
The ip helper-address command should be used on the Fa0/0 interface.
The 192.168.3.17 address has not been excluded from the 192Network pool.
24
Refer to the exhibit. From the output of the show interfaces
and ping commands, at which layer of the OSI model is a fault indicated?
application
transport
network
data link
physical
25
What three questions can be answered using data gathered from a baseline on a new network? (Choose three.)
Are areas of the network experiencing high error rates?
Will the disaster recovery procedures work correctly?
What parts of the network have the highest volume?
Does the organization require more network technicians?
How does the network perform during peak periods?
Are there any devices working at top capacity?
What networks are the most susceptible to security attacks?
26
Which type of ACL will permit traffic inbound into a private
network only if an outbound session has already been established between
the source and destination?
extended
reflexive
standard
time-based
27
Refer to the exhibit. R1 is performing NAT overload for the
10.1.1.0/24 inside network. Host A has sent a packet to Web Server. What
is the destination IP address of the return packet from Web Server when
received at R1?
10.1.1.2:80
10.1.1.2:1234
172.30.20.1:1234
172.30.20.1:3333
28
An administrator issues the command show interfaces s0/1/0 on a
router that is configured for Frame Relay. Which console output may
indicate an LMI mismatch?
Serial0/1/0 is administratively down
Serial0/1/0 is up, line protocol is up
Serial0/1/0 is up, line protocol is down
Serial0/1/0 is down, line protocol is down
29
A recently patched application server is experiencing response
time problems. The network on which the application server is located
has been experiencing occasional outages that the network team believes
may be related to recent routing changes. Network and application teams
have been notified to work on their respective issues. Which statement
applies to this situation?
Only results from the software package should be tested as the
network is designed to accommodate the proposed software platform.
Scheduling will be easy if the network and software teams work independently.
It will be difficult to isolate the problem if two teams are implementing changes independently.
Results from changes will be easier to reconcile and document if each team works in isolation.
30
Refer to the exhibit. Branch A has a non-Cisco router that is
using IETF encapsulation and Branch B has a Cisco router. After the
commands that are shown are entered, R1 and R2 fail to establish the
PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is
successfully established at both locations. Why is the PVC failing?
The PVC to R1 must be point-to-point.
LMI types must match on each end of a PVC.
The frame relay PVCs cannot be established between Cisco and non-Cisco routers.
The IETF parameter is missing from the frame-relay map ip 10.10.10.1 201 command.
31
Refer to the exhibit. Which VLAN will carry untagged traffic on FastEthernet 0/1?
VLAN 1
VLAN 2
VLAN 11
VLAN 12
VLAN 30
VLAN 999
32
What is an accurate description of CHAP when used with PPP on a serial connection between two routers?
A username and password are sent to the peer router, which replies with an accept or reject message.
A username and password are sent to the peer router. If these match
the configuration in the peer, the peer in turn provides a username and
password to the initiating router.
A challenge message is sent to
the peer router, which responds with its username and a calculated value
based on a shared secret. This value is then compared by the challenger
to its own calculations.
An encrypted password is sent to the peer router, which decrypts it
and compares it to a shared secret. If the decrypted passwords match,
the peer sends the encrypted password back to the initiating router.
33
Where does a service provider assume responsibility from a customer for a WAN connection?
local loop
DTE cable on router
demarcation point
demilitarized zone
34
Refer to the exhibit. An ACL called Managers already exists
on this router. What happens if the network administrator issues the
commands as shown in the exhibit?
The commands are added to the end of the existing ACL.
The existing Managers ACL will be overwritten by the new ACL.
The router will output an error message and no changes will be made.
A duplicate Managers ACL will be created that will contain only the new commands.
35
Which statement is true about PAP in the authentication of a PPP session?
PAP uses a two-way handshake.
The password is unique and random.
PAP conducts periodic password challenges.
PAP uses MD5 hashing to keep the password secure.
36
Which combination of Layer 2 protocol and authentication should
be used to establish a link without sending authentication information
in plain text between a Cisco and a non-Cisco router?
PPP with PAP
PPP with CHAP
HDLC with PAP
HDLC with CHAP
37
Which option correctly defines the capacity through the local loop guaranteed to a customer by the service provider?
BE
DE
CIR
CBIR
38
Which wireless solution can provide mobile users with non
line-of-sight broadband Internet access at speeds comparable to DSL or
cable?
Wi-Fi
WiMAX
satellite
Metro Ethernet
39
Refer to the exhibit. EIGRP has been configured as a routing
protocol on the network. Users on the 192.168.1.0/24 network should have
full access to the web server that is connected to 192.168.3.0/24 but
should not be allowed to telnet to router R3. Verifying the
configuration, the network administrator realizes that users on network
192.168.1.0/24 can successfully telnet to the router. What should be
done to remedy the problem?
The ACL 101 statements 10 and 20 should be reversed.
The ACL 101 should be applied on R3 VTY lines 0 4 in the inbound direction.
The ACL 101 should be applied on R3 VTY lines 0 4 in the outbound direction.
The ACL 101 should be applied on R3 Serial0/0/1 interface in the outbound direction.
The ACL 101 statement 10 should be changed to: permit ip 192.168.1.0 0.0.0.255 any
40
What does an access control list determine when used with NAT on a Cisco router?
addresses that are to be translated
addresses that are assigned to a NAT pool
addresses that are allowed out of the router
addresses that are accessible from the inside network
41
Which IP address and wildcard mask combination can be used in an ACL statement to match the 172.16.0.0/30 network?
172.16.0.0 0.0.0.1
172.16.0.0 0.0.0.3
172.16.0.0 0.0.0.7
172.16.0.0 255.255.255.252
42
Which security solution has the responsibility of monitoring
suspicious processes that are running on a host and that might indicate
infection of Trojan horse applications?
antivirus application
operating system patches
intrusion prevention system
Cisco Adaptive Security Appliance
43
Refer to the exhibit. A network administrator is trying to
connect R1 remotely to make configuration changes. Based on the
exhibited command output, what will be the result when attempting to
connect to R1?
failure to connect due to Telnet not being enabled
failure to connect due to incomplete configuration for Telnet
a successful connection and ability to make configuration changes
a successful connection but inability to make configuration changes because of the absence of an enable secret password
44
Refer to the exhibit. Results of the show vlan and show vtp
status commands for switches S1 and S2 are displayed in the exhibit.
VLAN 11 was created on S1. Why is VLAN 11 missing from S2?
There is a Layer 2 loop.
The VTP domain names do not match.
Only one switch can be in server mode.
S2 has a higher spanning-tree priority for VLAN 11 than S1 does.
45
A technician has been asked to run the Cisco SDM one-step
lockdown on a customer router. What will be the result of this process?
Traffic is only accepted from and forwarded to SDM-trusted Cisco routers.
Security testing is performed and the results are saved as a text file stored in NVRAM.
All traffic that enters the router is quarantined and checked for viruses before being forwarded.
The router is tested for any
potential security problems and all recommended security-related
configuration changes will be automatically applied.
46
Refer to the exhibit. Which data transmission technology is being represented?
TDM
PPP
HDLC
SLIP
47
A network administrator is instructing a technician on best
practices for applying ACLs. Which two suggestions should the
administrator provide? (Choose two.)
Named ACLs are less efficient than numbered ACLs.
Standard ACLs should be applied inside the core layer.
Place standard ACLs as close to the destination as possible.
ACLs applied to outbound interfaces require fewer router resources.
Extended ACLs should be applied closest to the source that is specified by the ACL.
48
Refer to the exhibit. Which configuration command would result in the output in the exhibit?
ip nat inside source static 10.1.200.254 172.16.76.3
ip nat inside source static 10.1.200.254 192.168.0.10
ip nat inside source static 172.16.76.3 10.1.200.254
ip nat inside source static 172.16.76.3 192.168.0.10
ip nat inside source static 192.168.0.10 172.16.76.3
ip nat inside source static 192.168.0.10 10.1.200.254
49
What are three important reasons to establish a network baseline? (Choose three.)
to determine the time it takes for the network to self recover from a failure
to determine which areas in the network are underutilized or overutilized
to determine the performance of the network during the normal hours of operation
to determine what thresholds should be set for the devices that need to be monitored
to determine the areas in the network which should not be included in the monitoring process
to determine the number of users whose access to network resources should be restricted
50
Which two statements are true about creating and applying access lists? (Choose two.)
There is an implicit deny at the end of all access lists.
One access list per port, per protocol, per direction is permitted.
Access list entries should filter in the order from general to specific.
The term “inbound” refers to traffic that enters the network from the router interface where the ACL is applied.
Standard ACLs should be applied closest to the source while extended ACLs should be applied closest to the destination.
51
While troubleshooting a problem with an e-mail server, an
administrator observes that the switch port used by the server shows
“up, line protocol up”. The administrator cannot ping the server. At
which layer of the OSI model is the problem most likely to be found?
application layer
network layer
data link layer
physical layer
52
Refer to the exhibit. Router RT is not receiving routing updates from router RTA. What is causing the problem?
The ip rip authentication key-chain command specifies exam rather than test.
The name of the keystring is not the name of the neighboring router.
The key chains are given the same name on both routers.
The passive-interface command was issued for RTA.
Ccna final exam - java, php, javascript, ios, cshap all in one. This is a collaboratively edited question and answer site for professional and enthusiast programmers. It's 100% free, no registration required.
Showing posts with label CCNA4 FINAL. Show all posts
Showing posts with label CCNA4 FINAL. Show all posts
Tuesday, May 22, 2012
Tuesday, December 28, 2010
CCNA 4 Final Exam V4.0 2010
1. What functionality do access control lists provide in the implementation of dynamic NAT on a Cisco router?
define which addresses can be translated
define which addresses are assigned to a NAT pool
define which addresses are allowed out the router
define which addresses can be accessed from the inside network
2. Which three guidelines would help contribute to creating a strong password policy? (Choose three.)
Once a good password is created, do not change it.
Deliberately misspell words when creating passwords.
Create passwords that are at least 8 characters in length.
Use combinations of upper case, lower case, and special characters.
Write passwords in locations that can be easily retrieved to avoid being locked out.
Use long words found in the dictionary to make passwords that are easy to remember.
3. Refer to the exhibit. Every time the administrator reboots this router, the boot process ends in setup mode. What is a possible problem?
There is insufficient RAM for the IOS to load on this router.
A password recovery process should be done on this router.
The bootstrap version and the version of the IOS are different.
The IOS image is damaged and must be reloaded using tftpdnld.
The configuration register is set to ignore the startup configuration.
define which addresses can be translated
define which addresses are assigned to a NAT pool
define which addresses are allowed out the router
define which addresses can be accessed from the inside network
2. Which three guidelines would help contribute to creating a strong password policy? (Choose three.)
Once a good password is created, do not change it.
Deliberately misspell words when creating passwords.
Create passwords that are at least 8 characters in length.
Use combinations of upper case, lower case, and special characters.
Write passwords in locations that can be easily retrieved to avoid being locked out.
Use long words found in the dictionary to make passwords that are easy to remember.
3. Refer to the exhibit. Every time the administrator reboots this router, the boot process ends in setup mode. What is a possible problem?
There is insufficient RAM for the IOS to load on this router.
A password recovery process should be done on this router.
The bootstrap version and the version of the IOS are different.
The IOS image is damaged and must be reloaded using tftpdnld.
The configuration register is set to ignore the startup configuration.
Friday, February 19, 2010
CCNA4 Final Exam (French)
Thanks IS_IS eigrp!
This is Final exam (French), if you have other test, please send to me at nguyenhuuhai.it@gmail.com thanks.
Download now
This is Final exam (French), if you have other test, please send to me at nguyenhuuhai.it@gmail.com thanks.
Download now
Monday, April 27, 2009
CCNA4 FINAL 100/100
1. Refer to the exhibit. A network administrator is trying to configure a router to use SDM. After this configuration shown in the exhibit is applied, the SDM interface of the router is still not accessible. What is the cause of the problem?
*The username and password are not configured correctly.
The authentication method is not configured correctly.
The HTTP timeout policy is not configured correctly.
The vtys are not configured correctly.
2. Refer to the exhibit. Branch A has a non-Cisco router that is using IETF encapsulation and Branch B has a Cisco router. After the commands that are shown are entered, R1 and R2 fail to establish the PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is successfully established at both locations. Why is the PVC failing?
The PVC to R1 must be point-to-point.
LMI types must match on each end of a PVC.
The frame relay PVCs cannot be established between Cisco and non-Cisco routers.
*The IETF parameter is missing from the frame-relay map ip 10.10.10.1 201 command.
3. Refer to the exhibit. An ACL called Managers already exists on this router. What happens if the network administrator issues the commands as shown in the exhibit?
The new ACL overwrites the existing ACL.
The network administrator will receive an error message.
*The existing ACL is modified to include the new command.
A second Managers ACL is created that contains only the new command.
4. Refer to the exhibit. A network administrator is trying to backup the IOS software on R1 to the TFTP server. He receives the error message that is shown in the exhibit, and cannot ping the TFTP server from R1. What is an action that can help to isolate this problem?
Use correct source file name in the command.
Verify that the TFTP server software is running.
Make sure that there is enough room on the TFTP server for the backup.
*Check that R1 has a route to the network where the TFTP server resides.
5. What can a network administrator do to recover from a lost router password?
use the copy tftp: flash: command
boot the router to bootROM mode and enter the b command to load the IOS manually
telnet from another router and issue the show running-config command to view the password
*boot the router to ROM monitor mode and configure the router to ignore the startup configuration when it initializes
6. Which combination of authentication and Layer 2 protocol should be used to establish a link between a Cisco and a non-Cisco router without sending authentication information in plain text?
CHAP and HDLC
*CHAP and PPP
PAP and HDLC
PAP and PPP
7. Refer to the exhibit. Which statement correctly describes how Router1 processes an FTP request that enters interface s0/0/0 and is destined for an FTP server at IP address 192.168.1.5?
The router matches the incoming packet to the statement that was created by the access-list 201 deny icmp 192.168.1.0 0.0.0.255 any command, continues comparing the packet to the remaining statements in ACL 201 to ensure that no subsequent statements allow FTP, and then the router drops the packet.
The router reaches the end of ACL 101 without matching a condition and drops the packet because there is no statement that was created by the access-list 101 permit ip any any command.
*The router matches the incoming packet to the statement that was created by the access-list 101 permit ip any 192.168.1.0 0.0.0.255 command and allows the packet into the router.
It matches the incoming packet to the statement that was created by the access-list 201 permit ip any any command and allows the packet into the router.
8. Which three statements accurately describe attributes of a security policy? (Choose three.)
*It creates a basis for legal action if necessary.
It should not be altered once it is implemented.
*It defines a process for managing security violations.
It focuses primarily on threats from outside of the organization.
*It defines acceptable and unacceptable use of network resources.
It provides step-by-step procedures to harden routers and other network devices.
9. Refer to the exhibit. The network administrator creates a standard access control list on Router1 to prohibit traffic from the 172.16.1.0/24 network from reaching the 172.16.2.0/24 network while still permitting Internet access for all networks. On which router interface and in which direction should it be applied?
interface Fa0/0, inbound
interface Fa0/0, outbound
interface Fa0/1, inbound
*interface Fa0/1, outbound
10. Refer to the exhibit. Why are the routers unable to establish a PPP session?
*The usernames are misconfigured.
The IP addresses are on different subnets.
The clock rate is configured on the wrong end of the link.
The CHAP passwords must be different on the two routers.
Interface serial 0/0/0 on Router1 must connect to interface serial 0/0/1 on Router2.
11. What are two main components of data confidentiality? (Choose two.)
checksum
digital certificates
**encapsulation
**encryption
hashing
12. A technician is talking to a colleague at a rival company and comparing DSL transfer rates between the two companies. Both companies are in the same city, use the same service provider, and have the same rate/service plan. What is the explanation for why company 1 reports higher download speeds than company 2 reports?
Company 1 only uses microfilters at branch locations.
Company 1 has a lower volume of POTS traffic than company 2 has.
**Company 2 is located farther from the service provider than company 1 is.
Company 2 shares the connection to the DSLAM with more clients than company 1 shares with.
13. What is the result when the command permit tcp 192.168.4.0 0.0.3.255 any eq 23 is entered in a named access control list and applied on the inbound interface of a router?
All traffic from 192.168.4.0/24 larger than 23 bytes is permitted.
FTP traffic from the 192.168.4.0/24 network is permitted.
TCP traffic destined to 192.168.4.0/24 network is permitted.
**Telnet traffic originating from 192.168.4.0/22 is permitted out.
14. What are two major characteristics of a worm? (Choose two.)
**exploits known vulnerabilities
attaches itself to another program
executed by a predefined time or event
masquerades as an accepted program
**copies itself to the host and selects new targets
15. While configuring a Frame Relay connection, when should a static Frame Relay map be used?
the remote router is a non-Cisco router
the local router is configured with subinterfaces
**broadcast traffic and multicast traffic over the PVC must be controlled
globally significant rather than locally significant DLCIs are being used
16. A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure static NAT.
Configure dynamic NAT.
Configure static NAT with overload.
**Configure dynamic NAT with overload.
17. Refer to the exhibit. Which DHCP requests will R1 answer?
all DHCP requests that R1 receives
requests that are broadcast to 10.0.1.255
DNS requests with a destination of 10.0.1.3
**requests that are received on the FastEthernet 0/0 interface
requests that come from any networks that are not listed as excluded
18. What are the symptoms when the s0/0/0 interface on a router is attached to an operational CSU/DSU that is generating a clock signal, but the far end router on the point-to-point link has not been activated?
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
**show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
19. A technician has been asked to run Cisco SDM one-step lockdown on the router of a customer. What will be the result of this process?
Traffic is only forwarded from SDM-trusted Cisco routers.
Security testing is performed and the results are saved as a text file stored in NVRAM.
**The router is tested for potential security problems and any necessary changes are made.
All traffic entering the router is quarantined and checked for viruses before being forwarded.
20. Refer to the exhibit. A network administrator has issued the commands that are shown on Router1 and Router2. A later review of the routing tables reveals that neither router is learning the LAN network of the neighbor router. What is most likely the problem with the RIPng configuration?
The serial interfaces are in different subnets.
**The RIPng process is not enabled on interfaces.
The RIPng processes do not match between Router1 and Router2.
The RIPng network command is missing from the IPv6 RIP configuration.
21. Refer to the exhibit. Which statement is true about the Frame Relay connection?
The Frame Relay connection is in the process of negotiation.
**A congestion control mechanism is enabled on the Frame Relay connection.
The “ACTIVE” status of the Frame Relay connection indicates that the network is experiencing congestion.
Only control FECN and BECN bits are sent over the Frame Relay connection. No data traffic traverses the link.
22. When configuring a Frame Relay connection, what is the purpose of Inverse ARP?
to assign a DLCI to a remote peer
to disable peer requests from determining local Layer 3 addresses
to negotiate LMI encapsulations between local and remote Frame Relay peers
**to create a mapping of DLCI to Layer 3 addresses that belong to remote peers
23. When NAT is in use, what is used to determine the addresses that can be translated on a Cisco router?
**access control list
routing protocol
inbound interface
ARP cache
24. An administrator is configuring a dual stack router with IPv6 and IPv4 using RIPng. The administrator receives an error message when trying to enter the IPv4 routes into RIPng. What is the cause of the problem?
When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of the newer technology.
Incorrect IPv4 addresses are entered on the router interfaces.
RIPng is incompatible with dual-stack technology.
**IPv4 is incompatible with RIPng.
25. Refer to the exhibit. Router1 is not able to communicate with its peer that is connected to this interface. Based on the output as shown, what is the most likely cause?
interface reset
**unplugged cable
improper LMI type
PPP negotiation failure
26. Which two functions are provided by the Local Management Interface (LMI) that is used in Frame Relay networks? (Choose two.)
**simple flow control
error notification
congestion notification
mapping of DLCIs to network addresses
**exchange of information about the status of virtual circuits
27. Refer to the exhibit. A technician issues the show interface s0/0/0 command on R1 while troubleshooting a network problem. What two conclusions can be determined by from the output shown? (Choose two.)
**The bandwidth has been set to the value of a T1 line.
This interface should be configured for PPP encapsulation.
**There is no failure indicated in an OSI Layer 1 or Layer 2.
The physical connection between the two routers has failed.
The IP address of S0/0/0 is invalid, given the subnet mask being used.
28. Refer to the exhibit. Which statement is true about the CSU/DSU device?
It connects asynchronous devices to a LAN or WAN through network and terminal emulation software.
It uses a multiport internetworking device to switch traffic such as Frame Relay, ATM, or X.25 over the WAN.
**It provides termination for the digital signal and ensures connection integrity through error correction and line monitoring.
It converts the digital signals produced by a computer into voice frequencies that can be transmitted over the analog lines of the public telephone network.
29. Where does a service provider assume responsibility from a customer for a WAN connection?
local loop
DTE cable on router
**demarcation point
demilitarized zone
30. What are two LCP options that can be configured for PPP? (Choose two.)
EAP
**CHAP
IPCP
CDPCP
**stacker
31. Refer to the exhibit. What is placed in the address field in the header of a frame that will travel from the DC router to the Orlando router?
DLCI 123
**DLCI 321
10.10.10.25
10.10.10.26
MAC address of the Orlando router
32. Which two statements are true about creating and applying access lists? (Choose two.)
**There is an implicit deny at the end of all access lists.
**One access list per port, per protocol, per direction is permitted.
Access list entries should filter in the order from general to specific.
The term “inbound” refers to traffic that enters the network from the router interface where the ACL is applied.
Standard ACLs should be applied closest to the source while extended ACLs should be applied closest to the destination.
33. Which statement is true about wildcard masks?
Inverting the subnet mask will always create the wildcard mask.
The wildcard mask performs the same function as a subnet mask.
A network or subnet bit is identified by a “1″ in the wildcard mask.
**IP address bits that must be checked are identified by a “0″ in the wildcard mask.
34. Refer to the exhibit. A host connected to Fa0/0 is unable to acquire an IP address from this DHCP server. The output of the debug ip dhcp server command shows “DHCPD: there is no address pool for 192.168.1.1″. What is the problem?
The 192.168.1.1 address has not been excluded from the DHCP pool.
**The pool of addresses for the 192Network pool is incorrect.
The default router for the 192Network pool is incorrect.
The 192.168.1.1 address is already configured on Fa0/0.
35.Refer to the exhibit. A network administrator is tasked with completing the Frame Relay topology that interconnects two remote sites. How should the point-to-point subinterfaces be configured on HQ to complete the topology?
frame-relay interface-dlci 103 on Serial 0/0/0.1
frame-relay interface-dlci 203 on Serial 0/0/0.2
**frame-relay interface-dlci 301 on Serial 0/0/0.1
frame-relay interface-dlci 302 on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 103 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 203 broadcast on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 301 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 302 broadcast on Serial 0/0/0.2
36. What are two effective measures for securing routers? (Choose two.)
Protect all active router interfaces by configuring them as passive interfaces.
Configure remote administration through VTY lines for Telnet access.
**Use quotes or phrases to create pass phrases.
**Disable the HTTP server service.
Enable SNMP traps.
37. A network administrator is instructing a technician on best practices for applying ACLs. Which suggestion should the administrator provide?
Named ACLs are less efficient than numbered ACLs.
Standard ACLs should be applied closest to the core layer.
ACLs applied to outbound interfaces are the most efficient.
**Extended ACLs should be applied closest to the source that is specified by the ACL.
38. Refer to the exhibit. RIPv2 has been configured on all routers in the network. Routers R1 and R3 do not receive RIP routing updates. On the basis of the provided configuration, what should be enabled on router R2 to remedy the problem?
proxy ARP
CDP updates
SNMP services
**RIP authentication
39. Refer to the exhibit. Partial results of the show access-lists and show ip interface FastEthernet 0/1 commands for router Router1 are shown. There are no other ACLs in effect. Host A is unable to telnet to host B. Which action will correct the problem but still restrict other traffic between the two networks?
Apply the ACL in the inbound direction.
Apply the ACL on the FastEthernet 0/0 interface.
**Reverse the order of the TCP protocol statements in the ACL.
Modify the second entry in the list to permit tcp host 172.16.10.10 any eq telnet .
40. What will be the result of adding the command ip dhcp excluded-address 192.168.24.1 192.168.24.5 to the configuration of a local router that has been configured as a DHCP server?
Traffic that is destined for 192.168.24.1 and 192.168.24.5 will be dropped by the router.
Traffic will not be routed from clients with addresses between 192.168.24.1 and 192.168.24.5.
**The DHCP server will not issue the addresses ranging from 192.168.24.1 to 192.168.24.5.
The router will ignore all traffic that comes from the DHCP servers with addresses 192.168.24.1 and 192.168.24.5.
41. Refer to the exhibit. What can be concluded from the exhibited output of the debug ip nat command?
The 10.10.10.75 host is exchanging packets with the 192.168.0.10 host.
The native 10.1.200.254 address is being translated to 192.168.0.10.
**The 192.168.0.0/24 network is the inside network.
Port address translation is in effect.
42. Refer to the exhibit. Company ABC expanded its business and recently opened a new branch office in another country. IPv6 addresses have been used for the company network. The data servers Server1 and Server2 run applications which require end-to-end functionality, with unmodified packets that are forwarded from the source to the destination. The edge routers R1 and R2 support dual stack configuration. What solution should be deployed at the edge of the company network in order to successfully interconnect both offices?
a new WAN service supporting only IPv6
NAT overload to map inside IPv6 addresses to outside IPv4 address
**a manually configured IPv6 tunnel between the edge routers R1 and R2
static NAT to map inside IPv6 addresses of the servers to an outside IPv4 address and dynamic NAT for the rest of the inside IPv6 addresses
43. A network administrator has changed the VLAN configurations on his network switches over the past weekend. How can the administrator determine if the additions and changes improved performance and availability on the company intranet?
**Conduct a performance test and compare with the baseline that was established previously.
Interview departmental secretaries and determine if they think load time for web pages has improved.
Determine performance on the intranet by monitoring load times of company web pages from remote sites.
Compare the hit counts on the company web server for the current week to the values that were recorded in previous weeks.
44. Refer to the exhibit. From the output of the show interfaces and ping commands, at which layer of the OSI model is a fault indicated?
application
transport
**network
data link
physical
45. While troubleshooting a problem with an e-mail server, an administrator observes that the switch port used by the server shows “up, line protocol up”. The administrator cannot ping the server. At which layer of the OSI model is the problem most likely to be found?
application layer
**network layer
data link layer
physical layer
46. Which variable is permitted or denied by a standard access control list?
protocol type
**source IP address
source MAC address
destination IP address
destination MAC address
47. A technician is editing and reapplying ACL 115 to a router, what is the result of adding the command access-list 115 permit tcp any 172.16.0.0 0.0.255.255 established to the ACL when it is reapplied to the router?
All traffic that comes from 172.16.0.0/16 will be allowed.
All TCP traffic that is destined for 172.16.0.0/16 is permitted.
Any SYN packets that are sent to 172.16.0.0/16 will be permitted.
**Responses to traffic that originates from the 172.16.0.0/16 network are allowed.
48. Because of a remote-procedure call failure, a user is unable to access an NFS server. At what layer of the TCP/IP model does this problem occur?
network layer
data link layer
physical layer
**application layer
49. Refer to the exhibit. Communication between two peers has failed. Based on the output that is shown, what is the most likely cause?
interface reset
unplugged cable
improper LMI type
**PPP negotiation failure
50. Which encapsulation protocol when deployed on a Cisco router over a serial interface is only compatible with another Cisco router?
PPP
SLIP
**HDLC
Frame Relay
*The username and password are not configured correctly.
The authentication method is not configured correctly.
The HTTP timeout policy is not configured correctly.
The vtys are not configured correctly.
2. Refer to the exhibit. Branch A has a non-Cisco router that is using IETF encapsulation and Branch B has a Cisco router. After the commands that are shown are entered, R1 and R2 fail to establish the PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is successfully established at both locations. Why is the PVC failing?
The PVC to R1 must be point-to-point.
LMI types must match on each end of a PVC.
The frame relay PVCs cannot be established between Cisco and non-Cisco routers.
*The IETF parameter is missing from the frame-relay map ip 10.10.10.1 201 command.
3. Refer to the exhibit. An ACL called Managers already exists on this router. What happens if the network administrator issues the commands as shown in the exhibit?
The new ACL overwrites the existing ACL.
The network administrator will receive an error message.
*The existing ACL is modified to include the new command.
A second Managers ACL is created that contains only the new command.
4. Refer to the exhibit. A network administrator is trying to backup the IOS software on R1 to the TFTP server. He receives the error message that is shown in the exhibit, and cannot ping the TFTP server from R1. What is an action that can help to isolate this problem?
Use correct source file name in the command.
Verify that the TFTP server software is running.
Make sure that there is enough room on the TFTP server for the backup.
*Check that R1 has a route to the network where the TFTP server resides.
5. What can a network administrator do to recover from a lost router password?
use the copy tftp: flash: command
boot the router to bootROM mode and enter the b command to load the IOS manually
telnet from another router and issue the show running-config command to view the password
*boot the router to ROM monitor mode and configure the router to ignore the startup configuration when it initializes
6. Which combination of authentication and Layer 2 protocol should be used to establish a link between a Cisco and a non-Cisco router without sending authentication information in plain text?
CHAP and HDLC
*CHAP and PPP
PAP and HDLC
PAP and PPP
7. Refer to the exhibit. Which statement correctly describes how Router1 processes an FTP request that enters interface s0/0/0 and is destined for an FTP server at IP address 192.168.1.5?
The router matches the incoming packet to the statement that was created by the access-list 201 deny icmp 192.168.1.0 0.0.0.255 any command, continues comparing the packet to the remaining statements in ACL 201 to ensure that no subsequent statements allow FTP, and then the router drops the packet.
The router reaches the end of ACL 101 without matching a condition and drops the packet because there is no statement that was created by the access-list 101 permit ip any any command.
*The router matches the incoming packet to the statement that was created by the access-list 101 permit ip any 192.168.1.0 0.0.0.255 command and allows the packet into the router.
It matches the incoming packet to the statement that was created by the access-list 201 permit ip any any command and allows the packet into the router.
8. Which three statements accurately describe attributes of a security policy? (Choose three.)
*It creates a basis for legal action if necessary.
It should not be altered once it is implemented.
*It defines a process for managing security violations.
It focuses primarily on threats from outside of the organization.
*It defines acceptable and unacceptable use of network resources.
It provides step-by-step procedures to harden routers and other network devices.
9. Refer to the exhibit. The network administrator creates a standard access control list on Router1 to prohibit traffic from the 172.16.1.0/24 network from reaching the 172.16.2.0/24 network while still permitting Internet access for all networks. On which router interface and in which direction should it be applied?
interface Fa0/0, inbound
interface Fa0/0, outbound
interface Fa0/1, inbound
*interface Fa0/1, outbound
10. Refer to the exhibit. Why are the routers unable to establish a PPP session?
*The usernames are misconfigured.
The IP addresses are on different subnets.
The clock rate is configured on the wrong end of the link.
The CHAP passwords must be different on the two routers.
Interface serial 0/0/0 on Router1 must connect to interface serial 0/0/1 on Router2.
11. What are two main components of data confidentiality? (Choose two.)
checksum
digital certificates
**encapsulation
**encryption
hashing
12. A technician is talking to a colleague at a rival company and comparing DSL transfer rates between the two companies. Both companies are in the same city, use the same service provider, and have the same rate/service plan. What is the explanation for why company 1 reports higher download speeds than company 2 reports?
Company 1 only uses microfilters at branch locations.
Company 1 has a lower volume of POTS traffic than company 2 has.
**Company 2 is located farther from the service provider than company 1 is.
Company 2 shares the connection to the DSLAM with more clients than company 1 shares with.
13. What is the result when the command permit tcp 192.168.4.0 0.0.3.255 any eq 23 is entered in a named access control list and applied on the inbound interface of a router?
All traffic from 192.168.4.0/24 larger than 23 bytes is permitted.
FTP traffic from the 192.168.4.0/24 network is permitted.
TCP traffic destined to 192.168.4.0/24 network is permitted.
**Telnet traffic originating from 192.168.4.0/22 is permitted out.
14. What are two major characteristics of a worm? (Choose two.)
**exploits known vulnerabilities
attaches itself to another program
executed by a predefined time or event
masquerades as an accepted program
**copies itself to the host and selects new targets
15. While configuring a Frame Relay connection, when should a static Frame Relay map be used?
the remote router is a non-Cisco router
the local router is configured with subinterfaces
**broadcast traffic and multicast traffic over the PVC must be controlled
globally significant rather than locally significant DLCIs are being used
16. A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure static NAT.
Configure dynamic NAT.
Configure static NAT with overload.
**Configure dynamic NAT with overload.
17. Refer to the exhibit. Which DHCP requests will R1 answer?
all DHCP requests that R1 receives
requests that are broadcast to 10.0.1.255
DNS requests with a destination of 10.0.1.3
**requests that are received on the FastEthernet 0/0 interface
requests that come from any networks that are not listed as excluded
18. What are the symptoms when the s0/0/0 interface on a router is attached to an operational CSU/DSU that is generating a clock signal, but the far end router on the point-to-point link has not been activated?
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
**show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
19. A technician has been asked to run Cisco SDM one-step lockdown on the router of a customer. What will be the result of this process?
Traffic is only forwarded from SDM-trusted Cisco routers.
Security testing is performed and the results are saved as a text file stored in NVRAM.
**The router is tested for potential security problems and any necessary changes are made.
All traffic entering the router is quarantined and checked for viruses before being forwarded.
20. Refer to the exhibit. A network administrator has issued the commands that are shown on Router1 and Router2. A later review of the routing tables reveals that neither router is learning the LAN network of the neighbor router. What is most likely the problem with the RIPng configuration?
The serial interfaces are in different subnets.
**The RIPng process is not enabled on interfaces.
The RIPng processes do not match between Router1 and Router2.
The RIPng network command is missing from the IPv6 RIP configuration.
21. Refer to the exhibit. Which statement is true about the Frame Relay connection?
The Frame Relay connection is in the process of negotiation.
**A congestion control mechanism is enabled on the Frame Relay connection.
The “ACTIVE” status of the Frame Relay connection indicates that the network is experiencing congestion.
Only control FECN and BECN bits are sent over the Frame Relay connection. No data traffic traverses the link.
22. When configuring a Frame Relay connection, what is the purpose of Inverse ARP?
to assign a DLCI to a remote peer
to disable peer requests from determining local Layer 3 addresses
to negotiate LMI encapsulations between local and remote Frame Relay peers
**to create a mapping of DLCI to Layer 3 addresses that belong to remote peers
23. When NAT is in use, what is used to determine the addresses that can be translated on a Cisco router?
**access control list
routing protocol
inbound interface
ARP cache
24. An administrator is configuring a dual stack router with IPv6 and IPv4 using RIPng. The administrator receives an error message when trying to enter the IPv4 routes into RIPng. What is the cause of the problem?
When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of the newer technology.
Incorrect IPv4 addresses are entered on the router interfaces.
RIPng is incompatible with dual-stack technology.
**IPv4 is incompatible with RIPng.
25. Refer to the exhibit. Router1 is not able to communicate with its peer that is connected to this interface. Based on the output as shown, what is the most likely cause?
interface reset
**unplugged cable
improper LMI type
PPP negotiation failure
26. Which two functions are provided by the Local Management Interface (LMI) that is used in Frame Relay networks? (Choose two.)
**simple flow control
error notification
congestion notification
mapping of DLCIs to network addresses
**exchange of information about the status of virtual circuits
27. Refer to the exhibit. A technician issues the show interface s0/0/0 command on R1 while troubleshooting a network problem. What two conclusions can be determined by from the output shown? (Choose two.)
**The bandwidth has been set to the value of a T1 line.
This interface should be configured for PPP encapsulation.
**There is no failure indicated in an OSI Layer 1 or Layer 2.
The physical connection between the two routers has failed.
The IP address of S0/0/0 is invalid, given the subnet mask being used.
28. Refer to the exhibit. Which statement is true about the CSU/DSU device?
It connects asynchronous devices to a LAN or WAN through network and terminal emulation software.
It uses a multiport internetworking device to switch traffic such as Frame Relay, ATM, or X.25 over the WAN.
**It provides termination for the digital signal and ensures connection integrity through error correction and line monitoring.
It converts the digital signals produced by a computer into voice frequencies that can be transmitted over the analog lines of the public telephone network.
29. Where does a service provider assume responsibility from a customer for a WAN connection?
local loop
DTE cable on router
**demarcation point
demilitarized zone
30. What are two LCP options that can be configured for PPP? (Choose two.)
EAP
**CHAP
IPCP
CDPCP
**stacker
31. Refer to the exhibit. What is placed in the address field in the header of a frame that will travel from the DC router to the Orlando router?
DLCI 123
**DLCI 321
10.10.10.25
10.10.10.26
MAC address of the Orlando router
32. Which two statements are true about creating and applying access lists? (Choose two.)
**There is an implicit deny at the end of all access lists.
**One access list per port, per protocol, per direction is permitted.
Access list entries should filter in the order from general to specific.
The term “inbound” refers to traffic that enters the network from the router interface where the ACL is applied.
Standard ACLs should be applied closest to the source while extended ACLs should be applied closest to the destination.
33. Which statement is true about wildcard masks?
Inverting the subnet mask will always create the wildcard mask.
The wildcard mask performs the same function as a subnet mask.
A network or subnet bit is identified by a “1″ in the wildcard mask.
**IP address bits that must be checked are identified by a “0″ in the wildcard mask.
34. Refer to the exhibit. A host connected to Fa0/0 is unable to acquire an IP address from this DHCP server. The output of the debug ip dhcp server command shows “DHCPD: there is no address pool for 192.168.1.1″. What is the problem?
The 192.168.1.1 address has not been excluded from the DHCP pool.
**The pool of addresses for the 192Network pool is incorrect.
The default router for the 192Network pool is incorrect.
The 192.168.1.1 address is already configured on Fa0/0.
35.Refer to the exhibit. A network administrator is tasked with completing the Frame Relay topology that interconnects two remote sites. How should the point-to-point subinterfaces be configured on HQ to complete the topology?
frame-relay interface-dlci 103 on Serial 0/0/0.1
frame-relay interface-dlci 203 on Serial 0/0/0.2
**frame-relay interface-dlci 301 on Serial 0/0/0.1
frame-relay interface-dlci 302 on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 103 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 203 broadcast on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 301 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 302 broadcast on Serial 0/0/0.2
36. What are two effective measures for securing routers? (Choose two.)
Protect all active router interfaces by configuring them as passive interfaces.
Configure remote administration through VTY lines for Telnet access.
**Use quotes or phrases to create pass phrases.
**Disable the HTTP server service.
Enable SNMP traps.
37. A network administrator is instructing a technician on best practices for applying ACLs. Which suggestion should the administrator provide?
Named ACLs are less efficient than numbered ACLs.
Standard ACLs should be applied closest to the core layer.
ACLs applied to outbound interfaces are the most efficient.
**Extended ACLs should be applied closest to the source that is specified by the ACL.
38. Refer to the exhibit. RIPv2 has been configured on all routers in the network. Routers R1 and R3 do not receive RIP routing updates. On the basis of the provided configuration, what should be enabled on router R2 to remedy the problem?
proxy ARP
CDP updates
SNMP services
**RIP authentication
39. Refer to the exhibit. Partial results of the show access-lists and show ip interface FastEthernet 0/1 commands for router Router1 are shown. There are no other ACLs in effect. Host A is unable to telnet to host B. Which action will correct the problem but still restrict other traffic between the two networks?
Apply the ACL in the inbound direction.
Apply the ACL on the FastEthernet 0/0 interface.
**Reverse the order of the TCP protocol statements in the ACL.
Modify the second entry in the list to permit tcp host 172.16.10.10 any eq telnet .
40. What will be the result of adding the command ip dhcp excluded-address 192.168.24.1 192.168.24.5 to the configuration of a local router that has been configured as a DHCP server?
Traffic that is destined for 192.168.24.1 and 192.168.24.5 will be dropped by the router.
Traffic will not be routed from clients with addresses between 192.168.24.1 and 192.168.24.5.
**The DHCP server will not issue the addresses ranging from 192.168.24.1 to 192.168.24.5.
The router will ignore all traffic that comes from the DHCP servers with addresses 192.168.24.1 and 192.168.24.5.
41. Refer to the exhibit. What can be concluded from the exhibited output of the debug ip nat command?
The 10.10.10.75 host is exchanging packets with the 192.168.0.10 host.
The native 10.1.200.254 address is being translated to 192.168.0.10.
**The 192.168.0.0/24 network is the inside network.
Port address translation is in effect.
42. Refer to the exhibit. Company ABC expanded its business and recently opened a new branch office in another country. IPv6 addresses have been used for the company network. The data servers Server1 and Server2 run applications which require end-to-end functionality, with unmodified packets that are forwarded from the source to the destination. The edge routers R1 and R2 support dual stack configuration. What solution should be deployed at the edge of the company network in order to successfully interconnect both offices?
a new WAN service supporting only IPv6
NAT overload to map inside IPv6 addresses to outside IPv4 address
**a manually configured IPv6 tunnel between the edge routers R1 and R2
static NAT to map inside IPv6 addresses of the servers to an outside IPv4 address and dynamic NAT for the rest of the inside IPv6 addresses
43. A network administrator has changed the VLAN configurations on his network switches over the past weekend. How can the administrator determine if the additions and changes improved performance and availability on the company intranet?
**Conduct a performance test and compare with the baseline that was established previously.
Interview departmental secretaries and determine if they think load time for web pages has improved.
Determine performance on the intranet by monitoring load times of company web pages from remote sites.
Compare the hit counts on the company web server for the current week to the values that were recorded in previous weeks.
44. Refer to the exhibit. From the output of the show interfaces and ping commands, at which layer of the OSI model is a fault indicated?
application
transport
**network
data link
physical
45. While troubleshooting a problem with an e-mail server, an administrator observes that the switch port used by the server shows “up, line protocol up”. The administrator cannot ping the server. At which layer of the OSI model is the problem most likely to be found?
application layer
**network layer
data link layer
physical layer
46. Which variable is permitted or denied by a standard access control list?
protocol type
**source IP address
source MAC address
destination IP address
destination MAC address
47. A technician is editing and reapplying ACL 115 to a router, what is the result of adding the command access-list 115 permit tcp any 172.16.0.0 0.0.255.255 established to the ACL when it is reapplied to the router?
All traffic that comes from 172.16.0.0/16 will be allowed.
All TCP traffic that is destined for 172.16.0.0/16 is permitted.
Any SYN packets that are sent to 172.16.0.0/16 will be permitted.
**Responses to traffic that originates from the 172.16.0.0/16 network are allowed.
48. Because of a remote-procedure call failure, a user is unable to access an NFS server. At what layer of the TCP/IP model does this problem occur?
network layer
data link layer
physical layer
**application layer
49. Refer to the exhibit. Communication between two peers has failed. Based on the output that is shown, what is the most likely cause?
interface reset
unplugged cable
improper LMI type
**PPP negotiation failure
50. Which encapsulation protocol when deployed on a Cisco router over a serial interface is only compatible with another Cisco router?
PPP
SLIP
**HDLC
Frame Relay
Subscribe to:
Posts (Atom)